Bogen Stereo System DST1 User Manual

DST1  
Digital Stereo Tuner  
Userʼs Manual  
© 2009 Bogen Communications, Inc.  
Specifications subject to change without notice.  
54-2188-01B 0910  
 
IMPORTANT  
CAUTION:TO PREVENT RISK OF ELECTRIC SHOCK,DO NOT RE-  
MOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICINGTO QUALIFIED PERSONNEL.  
The lightning flash with arrowhead symbol, within an  
equilateral triangle,is intended to alert the user to the  
presence of uninsulateddangerous voltage” within the  
product’s enclosure that may be of sufficient magni-  
tude to constitute a risk of electric shock to persons.  
The exclamation point within an equilateral triangle is  
intended to alert the user to the presence of impor-  
tant operating and maintenance (servicing) instructions  
in the literature accompanying the appliance.  
FCC Statement (Part 15) - Radio Frequency Interference  
The DST1 Digital StereoTuner generates and uses radio frequency energy and if  
not installed and used in strict accordance with the manufacturer's instructions,  
may cause interference to radio and television reception.Testing is being con-  
ducted for compliance with the limits for a Class B device in accordance with the  
specifications in Part 15 of the FCC Rules and Canadian D.O.C. regulations.This  
testing is designed to provide reasonable protection against such interference.  
However,there is no guarantee that interference will not occur in a particular in-  
stallation. If this equipment does cause interference to radio or television recep-  
tion, which can be determined by turning the DST1 unit off and on, the user is  
encouraged to try to correct the interference by one or more of the following  
measures:  
- Reorient the radio orTV receiving antenna.  
- Relocate the DST1 unit with respect to the radio orTV receiver or vice-versa.  
- Plug the DST1 unit into a different outlet so that it and the radio orTV receiver  
are on different branch circuits.  
If necessary,the user should consult the dealer or an experienced radio/television  
technician for additional suggestions.The user may find the following flyer, "Inter-  
ference: Defining the Source," helpful.This flyer was prepared by the Federal Com-  
munications Commission (FCC) and is available from their Consumer and  
3
 
BeforeYou Begin  
Your Bogen DST1 Digital Stereo Tuner incorporates the latest in PLL digital cir-  
cuitry for reliable performance for years to come.To get the maximum benefit  
from your Bogen product, please read all instructional materials provided with  
the unit.  
Package Contents  
(1) DST1 Digital StereoTuner  
(1) Remote Control  
(1) Set, Rack Ears  
(1) AM Radio Antenna (Loop)  
(1) FM Radio Antenna (Dipole)  
(1) Stereo Patch Cable (RCA)  
(1) User’s Manual  
Unpacking  
The DST1 is carefully checked before leaving the factory. Inspect the shipping  
carton and unit for damage caused by improper handling. If damage is found you  
must file a claim with the transportation company that delivered the product.  
Installing Rack Ears  
A pair of rack ears are included that allow the user to mount the DST1 in a  
standard 19" audio/electronics rack.To install the rack ears, refer to the diagram  
and follow these steps:  
1. Remove two screws from the side panel of the DST1 toward the front.  
2. Place one rack ear in proper  
position, paying attention to  
correct alignment.  
3. Reattach two screws.  
4. Repeat procedure for second  
rack ear, located on the  
other side of the unit.  
Important: Before installing the  
DST1 in a rack, the four attached  
feet must be unscrewed and removed  
from the bottom of the unit.  
4
 
Front Panel Controls  
1
3
5
7
DIGITAL AM/FM STEREO TUNER  
TUNING  
TUNING  
+
AM/FM  
ST/MO  
FUNCTION  
MEMORY  
POWER  
INTRO  
CHANNEL  
+
-
2
4
6
8
7
1. POWER: Turns power to the unit ON or OFF.  
2. Power LED: Lights to indicate that unit is powered ON.  
3. INTRO: Scans preset stations.  
4. MEMORY: Activates memory to save station preset.  
5. CHANNEL +/- : Manually scrolls through programmed presets.  
6. AM/FM: Switches between AM and FM operation.  
7. TUNING:Tunes station frequency down (-) or up (+).  
8. STEREO/MONO: Selects STEREO or MONO operation  
for selected FM station.  
Rear Panel Controls and Connectors  
1
4
5
7
FM  
GND  
GND  
AM  
MODEL: DST1  
L
R
FM  
75Ω  
120VAC  
60HZ  
0.15A  
RISK OF ELECTRIC  
SHOCK DO NOT OPEN  
VOLUME  
MONO  
STEREO  
300Ω  
AM LOOP  
2
3
6
1. 75-Ohm: FM Antenna input.  
2. 300-Ohm: FM Antenna input.  
3. AM LOOP: AM Antenna input.  
4. VOLUME: Attenuates output volume.  
5. MONO: Audio connection for mono applications.  
6. STEREO R/L: Audio connections for stereo applications.  
7. AC Line: Connects to 120V, 60 Hz AC mains.  
5
 
Remote Control  
AM/FM  
MEM  
1
2
4
+
CH  
3
4
+
TU  
TU  
5
7
3
6
CH  
INTRO  
ST/MO  
All of the front panel control functions can also be adjusted by the remote control.  
1. AM/FM: Switches between AM and FM operation.  
2. MEM: Activates MEMORY to save station preset.  
3. CH +/CH - : Manually scrolls through stations from available presets.  
4. TU -/TU + :Tunes station frequency down (-) or up (+).  
5. MUTE: Mutes audio output (not available on front panel).  
6. INTRO: Scans preset stations.  
7. ST/MO: Selects STEREO or MONO operation for selected FM station.  
Additional buttons function as follows:  
POWER  
VFD  
1
2
5
DIGITAL  
2
1
4
7
0
3
3
5
8
6
9
+
10  
P.CALL  
4
1. POWER:Turns power to the unit ON or OFF.  
2. VFD: Selects different bar graph displays.  
3. 1 – 0: Manually enter digits for desired preset.  
4. 10+: Selects range in multiples of ten, for preset stations greater than “10”.  
5. P.CALL:Allows entry of actual station numbers. Select a band (eitherAM or  
FM), then press the P.CALL button. Next, enter the station number.  
6
 
Antenna Connection  
FM Dipole Antenna  
The indoor dipole antenna provided should be adequate for normal FM  
reception.  
1. Connect the antenna leads to the two terminals marked 300 Ohms  
(FM and GND).  
2. Position the antenna for the best reception.Tack it to a wall or baseboard  
if possible.  
For reception when the DST1 is installed in a rack, an external antenna  
installed in accordance with National Electric Codes may be required.  
FM Coaxial cable connector  
For applications using coaxial cable, an FM 75-Ohm coaxial cable connector  
is provided.  
AM Loop Antenna  
The DST1 is provided with an external AM antenna for AM reception.  
1. Carefully pull the antenna lead from the holding notch in the antenna  
and unwind the lead from the loop.  
2. Connect the antenna leads to the terminals marked AM LOOP  
(AM and GND).  
3. Snap the antenna into the base to form a free-standing unit.  
4. Position the antenna for best reception. If desired, the antenna may be  
permanently mounted using screws through the two holes in the base.  
Audio Connections  
An audio patch cable is provided to make audio connections.  
1. Connect the two RCA plugs from one end of the cable to the R and L  
STEREO terminals on the DST1. (Note: For mono applications, connect  
one end of cable to the MONO terminal.)  
2. Connect the other end of the cable to a line-level input (Hi-Z) of an audio  
pre-amplifier.  
Operation  
Power  
Press the front panel POWER button to turn on the DST1.  
Turn the rear-mounted VOLUME control counterclockwise to attenuate  
audio output.Turn fully clockwise for full output.  
7
 
To Select a Band*  
Press the button marked AM/FM.The current band selected (either AM or  
FM) appears on the display.  
You can preset up to 60 stations total for both bands. Preset stations may be  
any combination of AM and FM stations. FM stations may be played in either  
stereo or mono. Press the STEREO/MONO button to change mode.  
ToTune a Station*  
Pressing the TUNING + or TUNING - button advances to the next fre-  
quency. Pressing and holding the TUNING + or TUNING - button will ac-  
tivate the auto search feature.The word AUTO appears on the display, and the  
search will continue to the next clear station signal.To stop the auto search  
at any frequency, press either the TUNING + or TUNING - button again.  
To Preset Stations*  
1. Select a band and tune the first desired station.  
2. Press the MEMORY button and then one of the CHANNEL +/- buttons  
to select the preset number.The two-digit preset number appears on the  
display.The display flashes twice and then the preset is stored.  
3. Repeat the procedure for each desired preset.  
To Scan Preset Stations*  
1. Press the button marked INTRO. Each preset station will play for a few  
seconds in turn while scanning.  
2. To select a station during scanning, press the INTRO button again.  
To Select Preset Stations Using Remote Control  
The number buttons can be used to select a specific preset station. For  
presets greater than 10, press 10+ for each multiple of 10 (for example, 10,  
20, 30, etc.), then select the preset in that multiple.  
Example:To select preset 52, press 10+ five times, then press 2.  
Pressing P.CALL allows actual station numbers to be entered.  
1. Select a band.  
2. Press the P.CALL button.  
3. Enter the Station numbers.  
* Note: These functions are the same whether accessed from the front  
panel of the DST1 or from the Remote Control.  
8
 
Specifications  
Band Coverage:  
FM: 87.00 to 108.05 MHz  
AM: 530 to 1710 kHz  
Tuning:  
Channel Indicator:  
StationTuning:  
PLL Synthesizer  
Alphanumeric, fluorescent display  
Pushbutton  
Preset Memory:  
Memory Scan:  
60Total stations (FM and AM)  
Preset stations  
Antenna Connectors:  
FM: 75-ohm, coaxial: 300-ohm, push-release  
AM: Push-release  
Output:  
Program Selection:  
OutputTerminals:  
Controls:  
Stereo/Mono Out via RCA jacks; 1V minimum  
Pushbutton, via front panel or Remote Control  
RCA Jacks  
Power, Intro, Memory, Channel,  
AM/FM,Tuning, Stereo/Mono,Volume  
AM Loop and FM Dipole antennas  
Remote Control (Uses two AAA batteries)  
Stereo Patch Cable (RCA)  
Rack Ears (2)  
Accessories Included:  
OperatingVoltage:  
Dimensions:  
120V AC nominal, 60 Hz, 0.15A max.  
16-7/8"W × 1-3/4" H × 10" D (without feet)  
16-7/8"W × 2" H × 10" D (with feet attached)  
4.75 lb.  
Weight:  
9
 
LimitedWarranty, Exclusion of Certain Damages  
The Bogen DST1 Digital StereoTuner is warranted to be free from defects in material and work-  
manship for two (2) years from the date of sale to the original purchaser.Any part of the product  
covered by this warranty that, with normal installation and use, becomes defective (as confirmed  
by Bogen upon inspection) during the applicable warranty period, will be repaired or replaced by  
Bogen, at Bogen’s option, provided the product is shipped insured and prepaid to: Bogen Factory  
Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. Repaired or replacement product  
will be returned to you freight prepaid.This warranty does not extend to any of our products that  
have been subjected to abuse,misuse,improper storage,neglect,accident,improper installation or  
have been modified or repaired or altered in any manner whatsoever,or where the serial number  
or date code has been removed or defaced.  
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE  
WARRANTYANDTHE PURCHASER’S SOLEAND EXCLUSIVE REMEDY.BOGEN  
MAKES NO OTHERWARRANTIES OFANY KIND,EITHER EXPRESS OR IMPLIED,  
AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE  
MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability arising out of the manufac-  
ture, sale or supplying of products or their use or disposition,whether based upon warranty,con-  
tract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL  
BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAM-  
AGES (INCLUDING, BUT NOT LIMITEDTO, LOSS OF PROFITS, LOSS OF DATA  
OR LOSS OF USE DAMAGES)ARISING OUT OFTHE MANUFACTURE, SALE OR  
SUPPLYING OF PRODUCTS,EVEN IF BOGEN HAS BEENADVISED OFTHE POS-  
SIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the exclusion or  
limitation of incidental or consequential damages, so the above limitation or exclusion may not  
apply to you.This warranty gives you specific legal rights,and you may also have other rights which  
vary from State to State.  
Products that are out of warranty will also be repaired by the Bogen Factory Service Department  
– same address as above or call 201-934-8500.The parts and labor involved in these repairs are  
warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping  
charges in addition to parts and labor charges will be at the owner's expense.All returns require  
a Return Authorization number. For most efficient warranty or repair service, please include a  
description of the failure.  
12/2008  
10  
 
11  
 
50 Spring Street, Ramsey, New Jersey 07446, USA  
Tel. 201-934-8500 • Fax: 201-934-9832  
 

BenQ Projector cp270 User Manual
Black Decker Vacuum Cleaner 90510266 User Manual
Briggs Stratton Pressure Washer 020212 1 User Manual
Brookstone Watch 618009 User Manual
Cambridge Audio Stereo Amplifier 340A User Manual
Campbell Hausfeld Speaker System IFK003 User Manual
Canon Film Camera QL17 User Manual
Carrier Air Compressor 06D User Manual
Chromalox Electric Heater PG412 10 User Manual
Cisco Systems IP Phone OL 8148 01 User Manual