Bogen Speaker MPS1B User Manual

MPS1  
Mini Pendant Speaker  
Models MPS1B/MPS1W  
Installation and Use Manual  
© 2010 Bogen Communications, Inc.  
All rights reserved.  
Specifications subject to change without notice.  
54-2194-01A 1010  
 
TO SPEAKER  
ANCHOR  
POINT  
MPS1 Speaker Cable Connections  
and Suspension Instructions  
In addition to the Main suspension Drop Cable,  
a backup Safety Cable is required for proper  
installation. Use wire rope or other drop line rated  
for at least 100 lbs. to ensure a safety margin.  
The attachment point on the structure from which  
the speaker is to be anchored also must be able  
to handle 100 lbs.  
MAIN  
DROP  
CABLE  
SAFETY  
CABLE  
NOTE: If using suspension cables with a cladding,  
be sure to strip away coating where any clamping  
device is being used so that bare wire cores of the  
cable are being clamped.  
MPS1 SUSPENSION  
ATTACHMENT  
MPS1  
MINI PENDANT  
SPEAKER  
SAFETY  
MAIN DROP  
CABLE HOLE  
CABLE HOLE  
ALONG WITH THE MAIN DROP CABLE, YOU MUST ALSO USE A  
SAFETY CABLE WHEN SUSPENDING AN MPS1 PENDANT SPEAKER.  
BE SURE TO SECURE ALL RIGGING POINTS AND FOLLOW ALL  
THE CABLE MANUFACTURER’S MATERIAL RECOMMENDATIONS  
& INSTALLATION INSTRUCTIONS. FAILURE TO DO SO MAY RESULT  
IN PROPERTY DAMAGE, INJURY OR DEATH, AND LEGAL LIABILITY  
FOR YOU AND/OR YOUR COMPANY.  
Attach the main drop cable to the MPS1 Main Drop Cable hole in the Suspension  
Attachment located on the top of the speaker. This Main Drop Cable will be the primary  
connection that will hold all the suspended speakerʼs weight to the anchor point.  
Likewise, attach the Safety Cable to the Safety Cable hole in the Suspension Attachment.  
This Safety Cable is meant to be a safeguard only, so when attaching to an anchor point  
allow for a small amount of slack in the wire, as the Safety Cable should not bear any of  
the speakerʼs direct supension weight to keep the speaker hanging level.  
IMPORTANT: The MPS1 Mini Pendant is not an outdoor speaker. DO NOT expose the  
speaker to rain or moisture. The MPS1 should be installed by qualified personnel.  
 
Technical Specifications  
Frequency Response (-10dB)*  
Driver Complement  
Sensitivity (1W/1m)  
Impedance Range  
50Hz to 14kHz  
4-1/2” Dual-Cone Wide-Range  
85dB (Average 100Hz – 10kHz)  
Low (16 Ohms) / High (70V)  
50W @ 16 Ohms; 32W @ 70V  
70V: 32, 16, 8, 4, 2, 1  
Power Input (Maximum)  
Power Settings (in watts)**  
Enclosure Material  
Grille Material  
ABS Plastic Injection-Molded  
Powder-Coated Perforated Steel  
2 Terminal Quick-Disconnect Connector  
4 lb. 8 oz.  
Terminations  
Product Weight  
Speaker Dimensions  
Included Accessory  
Optional Accessories  
Enclosure Finish & Color  
12” Dia.. x 7-7/8” High  
(1) Quick-Disconnect Input Connector  
Hanging Cable Kit (CK10, white or black)  
Textured White or Black  
* Free-Space Response, 16-ohm input  
** Rear Panel switch selected  
Limited Warranty; Exclusion of Certain Damages  
The Bogen MPS1 Mini Pendant Speaker is warranted to be free from defects in material or workmanship for two (2) years from the date  
of sale to the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective  
will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service  
Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product will be returned to you freight prepaid. This warranty does not ex-  
tend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper installation or have  
been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has been removed or defaced.  
THE FOREGOING LIMITED WARRANTY IS BOGEN'S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER'S SOLE AND  
EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL  
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR  
A
PARTICULAR PURPOSE ARE HEREBY  
DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability arising out of the manufacture,  
sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be  
limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT  
OF THE MANUFACTURE, SALE OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGES OR LOSSES. Some States do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have  
other rights which vary from State to State.  
Products that are out of warranty will also be repaired by the Bogen Factory Service Department — same address as above or call  
201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service  
Department. All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns require a Return  
Authorization number.  
7/22/2008  
50 Spring Street, Ramsey, NJ 07446 USA  
Tel. 201-934-8500 • Fax: 201-934-9832  
 

Bionaire Humidifier BCM7205 User Manual
Bosch Power Tools Saw 1590EVSK User Manual
Boston Acoustics Automobile Parts SL80 User Manual
Bravetti Convection Oven CO200B User Manual
Brinkmann Landscape Lighting Candle Glow Garden Lanterns User Manual
Cadco Microwave Oven CAPO 803 User Manual
Cal Flame Hot Tub Spa Home Resort User Manual
Campbell Hausfeld Impact Driver CL250200AV User Manual
Chief Manufacturing Indoor Furnishings FSA 100 User Manual
Christie Digital Systems Projector LWU420 User Manual