Bogen Music Mixer MIC1X User Manual

MIC1X  
THRESH  
DUR  
G
A
T
E
LIMIT  
GAIN  
TREB  
BASS  
MIC1X  
Microphone Input  
Module  
MIC IN  
G
1
2
3
Features  
Transformer-balanced  
Gain/Trim control  
Bass and treble  
Gating  
Gating threshold and duration adjustments  
Variable Threshold Limiter  
Limiter Activity LED  
4 levels of available priority  
Can be muted from higher priority modules  
Can mute lower priority modules  
© 2001 Bogen Communications, Inc.  
54-2052-01C 0701  
Specifications subject to change without notice.  
 
Module Installation  
Jumper Selections  
Priority Level*  
1. Turn off all power to the unit.  
PRIORITY LEVEL  
2. Make all necessary jumper selections.  
This module can respond to 4 different levels of priority.  
Priority 1 is the highest priority. It mutes modules with  
lower priorities and is never muted. Priority 2 can be muted  
by Priority 1 modules and mutes modules set for 3 or 4.  
Priority 3 is muted by either Priority 1 or 2 modules and  
mutes Priority 4 modules. Priority 4 modules are muted by  
all higher priority modules.  
1
2
4
3
(Highest)  
(Lowest)  
3. Position module in front of desired module bay  
opening, making sure that the module is right-  
side up.  
J6 J7 J8  
J6 J7 J8  
J6 J7 J8  
J6 J7 J8  
4. Slide module on to card guide rails. Make sure  
that both the top and bottom guides are  
engaged.  
BUS  
GATING  
J6 J7 J8  
ASSIGNMENT  
* The number of priority levels available is determined by  
the amplifier the modules are used in.  
Enabled  
J4  
Bus  
B
Both  
J5  
A
J4  
5. Push the module in to the bay until the faceplate  
contacts the unit’s chassis.  
J5  
J5  
Disabled  
Gating  
J4  
PHANTOM  
POWER  
6. Use the two screws included to secure the mod-  
ule to the unit.  
J5  
Gating (turning off) of the modules output when insuffi-  
cient audio is present at the input can be disabled.  
Detection of audio for the purpose of muting lower prior-  
ity modules is always active regardless of jumper setting.  
Mono  
On  
J2  
Off  
WARNING:  
Turn off power to unit and make all jumper  
selections before installing module in unit.  
J2  
Phantom Power  
24V phantom power can be supplied to condenser microphones  
when jumper is set to ON position. Leave OFF for dynamic mics.  
J2  
Bus Assignment  
This module can be set to operate so that the MIC signal can be sent  
to the main unit’s A bus, B bus, or both buses.  
Gate -Threshold (Thresh)  
Gate - Duration (Dur)  
Controls the minimum necessary input signal level to turn the module’s out-  
put on and apply signal to the main unit's buses. Clockwise rotation increas-  
es the necessary signal level required to produce output and mute lower  
priority modules.  
Controls the amount of time the output and mute signal of the module  
remains applied to the main unit’s buses after the input signal falls below the  
required minimum signal level (set by the threshold control).  
MIC1X  
THRESH  
DUR  
G
A
T
E
LIMIT  
GAIN  
TREB  
BASS  
Bass &Treble (Treb)  
Limiter (Limit)  
Provides separate controls for Bass andTreble cut and boost.The Bass control  
affects frequencies below 100 Hz and Treble affects frequencies above 8 kHz.  
Clockwise rotation provides boost, counterclockwise rotation provides cut.  
Center position provides no affect.  
Sets the signal level threshold at which the module will begin to limit the  
level of its output signal. Clockwise rotation will allow more output signal  
before limiting, counterclockwise rotation will allow less.The limiter moni-  
tors the module’s output signal level,so increasing Gain will affect when lim-  
iting takes place.An LED indicates when the Limiter is active.  
MIC IN  
G
1
2
3
Connections  
Gain  
Uses standard female XLR to make connections to the module’s input. The  
input is low-impedance, transformer-balanced for excellent noise and ground  
loop immunity.  
Provides control over the level of input signal that can be applied to the  
internal signal buses of the main unit. Allows a way to balance the input lev-  
els of various devices so that the main unit controls can be set to relative-  
ly uniform or optimum levels.  
 

Billy Goat Blower QB501CE User Manual
Black Decker Vacuum Cleaner DV9610PN User Manual
Blodgett Convection Oven CNV14E User Manual
BlueAnt Wireless Bluetooth Headset Z9i User Manual
Bosch Appliances Home Security System Divar Series User Manual
Bosch Appliances Range HBL 73 User Manual
Cabletron Systems Switch FDDI User Manual
Canon Camera Lens 23569 User Manual
Carson Stereo Amplifier HA 150 10 User Manual
Casio Digital Camera K1160PCM2DMX User Manual