657
BLOOMFIELD INDUSTRIES
2 ERIK CIRCLE, P.O.Box 280
Verdi, NV 89439 U.S.A.
Customer Service (775) 345-0444 Ext.502
fax (775) 345-0569
OWNERS
MANUAL
LX
AIRPOT &
THERMAL
BREWERS
MODELS
2280
2282
2286EX
2288EX
Includes
INSTALLATION
OPERATION
USE & CARE
SERVICE
Model 2282
shown with
optional
airpot
p/n 75209 Rev. E
M657 050209 cps
TABLE OF CONTENTS
WARRANTY STATEMENT
xi
1
2
3
5
5
6
7
8
Thank You for purchasing this
Bloomfield Industries appliance.
SPECIFICATIONS
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
INSTALLATION INSTRUCTIONS
AGENCY APPROVAL INFORMATION
OPERATION
Proper installation, professional
operation and consistent
maintenance of this appliance will
ensure that it gives you the very
best performance and a long,
economical service life.
USERS GUIDE
CLEANING INSTRUCTIONS
SERVICING INSTRUCTIONS
Operational Adjustments
Electrical
Plumbing
De-liming Heater Tank
Diagnostics & Troubleshooting
EXPLODED VIEW & PARTS LIST
AirpotBrewerModels
9
10
12
14
15
This manual contains the
information needed to properly
install this appliance, and to use,
care for and maintain or repair the
appliance in a manner which will
ensure its optimum performance.
16
18
Thermal Brewer Models
WIRING DIAGRAMS
Airpot/Thermal Brewer Models
Export 240V thermal/airpot brewer
20
21
SPECIFICATIONS
ELECTRICAL SPECIFICATIONS*
MODEL
2280
WATTS
1800
VOLTS Hz
CIRCUIT REQUIRED
15 AMP (NEMA 5-15R)
15 AMP (NEMA 5-15R)
WIRE
120
120
50/60
50/60
2 + ground
2 + ground
2282
1800
Canada 1500 watts
MODEL
WATTS
3200
VOLTS
240
HZ.
CIRCUIT REQ.
WIRE
2286EX
2288EX
HARD WIRED
TO BREAKER
50/60
2 + GND.
DIMENSIONS*
OVER ALL
DEPTH
MODEL
CONFIGURATION
Thermal Brewer
Airpot Brewer
HEIGHT
WIDTH
2280/2286EX
2282/2288EX
27p (699 mm)
23p (599 mm)
9b (231 mm)
9b (231 mm)
22 D” (575 mm)
22 D” (575 mm)
* for complete information regarding specifications and dimensions, please consult the GLD (General
Layout Data) for the appliance ( p/n 75054).
1
FEATURES & OPERATING CONTROLS
CONTROL
PANEL
HOT WATER
FAUCET
CONTROL
PANEL
BREW
CHAMBER
HOT WATER
FAUCET
NAMEPLATE
NAMEPLATE
BREW
CHAMBER
THERMAL
SERVER
(BREWING
POSITION)
AIRPOT
(BREWING
POSITION)
THERMAL BREWER
AIRPOT BREWER
POSITIONING
BRACKET
1
2
3
CONTROL
PANEL
8
5
6
7
1.
2.
3.
5.
6.
7.
8.
Brew Indicator
Heat Indicator
Power Indicator
Brew Switch
Cancel Switch
Power Switch
Glows during brew cycle, flashes in “Brew Wait”
Glows when heating elements are energized
Glows when power is on
Press to initiate brew cycle
Press to terminate brew cycle
Press to turn brewer on or off
Dispense up to 2 cups of hot water at a time for tea, etc.
Hot Water Faucet
2
PRECAUTIONS AND GENERAL INFORMATION
WARNING: Electric Shock Hazard
All servicing requiring access to non-insulated components must be performed by qualified
service personnel. Do not open any access panels which require the use of tools. Failure to
heed this warning can result in electrical shock.
WARNING: Injury Hazard
All installation procedures must be performed by qualified personnel with full knowledge of all
applicable electrical and plumbing codes. Failure could result in property damage and
personal injury.
WARNING Electric Shock Hazard
Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a
plumbing line will provide such a ground. Electrical shock will cause death or serious Injury.
WARNING: Burn Hazard
This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from
contact with dispensed liquids.
This appliance is intended for commercial use only.
CAUTION: Equipment
Electrical Damage
This appliance is intended for use to brew beverage products for
human consumption. No other use is recommended or
authorized by the manufacturer or its agents.
DO NOT plug in or
energize this appliance until all
Installation Instructions are read
and followed. Damage to the
Brewer will occur if these
instructions are not followed.
This appliance is intended for use in commercial establishments,
where all operators are familiar with the appliance use,
limitations and associated hazards. Operating instructions and
warnings must be read and understood by all operators and
users.
CAUTION: Burn Hazard
To avoid splashing or
overflowing hot liquids,
Except as noted, this piece of equipment is made in the USA
and has American sizes on hardware. Please note: Metric
hardware is used to mount the inlet (Fill) solenoid. All metric
conversions are approximate and can vary in size.
ALWAYS use an empty airpot or
thermal server before starting the
brew cycle. Failure to comply can
cause serious burns.
The following trouble shooting, component views and parts lists
are included for general reference, and are intended for use by
qualified service personnel.
CAUTION: Burn Hazard
After a brew cycle, brew
basket contents are HOT.
Remove the brew basket and
dispose of used grounds with
care. Failure to comply can cause
serious burns.
This manual should be considered a permanent part of this
appliance. The manual must remain with the appliance if it is
sold or moved to another location.
CAUTION: Burn Hazard
Exposed surfaces of the
appliance, brew basket
and airpot or server may be HOT
to the touch, and can cause
serious burns.
3
INSTALLATION INSTRUCTIONS
READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION
IMPORTANT:
REFER TO EXPLODED VIEWS PAGES 16 thru 19 FOR
|