Bissell Pet Care Product 87R4 User Manual

Pet Hair Eraser  
C O R D E D H A N D V A C U U M  
U S E R ’ S G U I D E  
8 7 R 4 S E R I E S 2 2 0 - 2 4 0 V  
3
Safety Instructions  
4
Product View  
4
Assembly  
4-5  
Operations  
5-6  
Maintenance and Care  
6
Troubleshooting  
7
Consumer Services  
7
Replacement Parts  
8
Warranty  
ug110-4076_87R4E_1008.indd  
1
12/10/08 3:31:18 PM  
 
IMPORTANT SAFETY INSTRUCTIONS  
When using an electrical appliance,  
basic precautions should be observed,  
including the following:  
Remove plug from electrical outlet before cleaning or  
maintaining the appliance.  
If the supply cord is damaged, it must be replaced by  
the manufacturer or its service agent in order to avoid a  
hazard.  
Do not pick up toxic material (chlorine bleach,  
ammonia, drain cleaner, petrol, etc.).  
Do not use for any purpose other than described in  
this User’s Guide.  
READ ALL INSTRUCTIONS  
BEFORE USING YOUR  
UPRIGHT VACUUM.  
Use only manufacturer’s recommended attachments.  
Do not use with any opening blocked; keep free of  
dust, lint, hair, and anything that may reduce air flow.  
Keep appliance on a level surface.  
Turn off all controls before unplugging.  
Be extra careful when cleaning stairs.  
This appliance is provided with double  
insulation. Use only identical replacement parts.  
Do not use without debris tank and/or filters in place.  
Pay close attention when working  
around children.  
WARNING:To reduce  
the risk of fire, electric shock,  
or injury:  
Do not use outdoors or on wet surfaces.  
Do not leave machine when it is plugged in.  
Do not use with damaged cord or plug.  
If appliance is not working as it should, has been  
dropped, damaged, left outdoors, or dropped into water,  
return it to a service agent.  
Do not handle unit with wet hands.  
Do not pull or carry by cord, use cord as a handle, close  
SAVE THESE  
door on cord, pull cord around sharp corners or edges, run  
appliance over cord, or expose cord to heated surfaces.  
Do not unplug by pulling on cord. Unplug by  
grasping plug.  
INSTRUCTIONS.  
THIS MODEL IS FOR HOUSEHOLD USE ONLY.  
Do not run appliance over cord.  
Do not handle plug or appliance with wet hands.  
IMPORTANT  
Do not expose hair, loose clothing, fingers or body  
FOR OPERATION ON A 220-240 VOLT A.C. 50/60 Hz  
POWER SUPPLY ONLY.  
parts to openings or moving parts.  
Do not pick up hot or burning objects such as  
cigarettes, matches, or hot ashes.  
Do not pick up flammable or combustible materials (lighter  
fluid, petrol, kerosene, etc.) or use in the  
presence of explosive liquids or vapour.  
If your appliance is fitted with a nonrewireable BS 1363  
plug it must not be used unless a 13 amp (ASTA approved  
to BS 1362) fuse is fitted in the carrier contained in  
the plug. (Spares may be obtained from your BISSELL  
supplier). If for any reason the plug is cut off, it must be  
disposed of, as it is an electric shock hazard should it be  
inserted into a mains socket.  
Do not use appliance in an enclosed space filled with  
vapours given off by oil base paint, paint  
thinner, some moth proofing substances, flammable dust,  
or other explosive or toxic vapours.  
Not intended for use by persons (including  
children) with reduced sensory or mental capabilities, or  
lack of experience and knowledge, unless they have  
been given supervision or instruction concerning use of  
the appliance by a person responsible for their safety  
Young children should be supervised to ensure that they do  
not play with the appliance.  
3
w w w . b i s s e l l . c o m  
ug110-4076_87R4E_1008.indd  
3
12/10/08 3:31:18 PM  
 
Product view  
Handle  
Power Switch  
Dirt Container  
Release Latch  
Dirt Container  
Nozzle Release  
Button  
Flexible Rubber  
Contour Nozzle  
Power Cord with  
Cord Wrap System  
Filter Screen  
HEPA Media Filter  
Exhaust  
Assembly  
Your unit will come assembled and will require  
no tools to put together.  
Operations  
Power switch  
The power switch is located on the end of the curved  
handle.  
To turn hand vacuum ON ( I ), press up.  
To turn hand vacuum OFF ( 0 ), press down.  
2.  
Cleaning with hard nozzle  
1. Turn hand vacuum OFF.  
2. Remove flexible rubber contour nozzle by  
pressing down on round nozzle release  
button.  
3. Replace with hard nozzle by lining up the  
bottom of nozzle to the bottom of the dirt  
container. Pivot upwards to snap into place.  
3.  
4. Make sure the nozzle has snapped securely  
into place before using.  
w w w . b i s s e l l . c o m  
4
ug110-4076_87R4E_1008.indd  
4
12/10/08 3:31:19 PM  
 
Operations  
2.  
Cleaning with flexible rubber contour nozzle  
3.  
1. Turn hand vacuum OFF.  
2. Remove hard nozzle by pressing down on  
round nozzle release button.  
3. Replace with flexible rubber contour nozzle by lining  
up the bottom of nozzle to the bottom of the dirt  
container. Pivot upwards until it snaps into place.  
4. Make sure the nozzle has snapped securely  
into place before using  
Emptying the dirt container  
Empty the dirt container after each use. A  
full dirt container may reduce suction or  
performance of vacuum.  
1. Turn hand vacuum OFF.  
2. Unplug hand vacuum from electrical outlet.  
3. Press dirt container release latch down to  
disconnect dirt container and filter assembly  
from the unit.  
ATTENTION:  
For best performance,  
dirt container and filter  
assembly should be  
cleaned after every use.  
4. Remove filter by grasping tabs on both sides  
of filter frame and pulling away from the dirt  
container. For best results, periodically tap filter  
assembly against trash can to remove dirt that  
has collected on the screen and filter.  
3.  
4.  
6.  
5. Empty dirt into trash can.  
6. Replace filter assembly by aligning side  
labeled “TOP” into top of dirt container.  
Grasp filter tabs and press firmly to ensure  
filter assembly is secure in dirt container.  
5.  
7.  
NOTE: Make sure side of filter assembly  
labeled "TOP" faces outward when inserting  
filter assembly into dirt container.  
7. Reattach dirt container to unit by aligning  
bottom of dirt container to bottom of unit.  
Pivot upwards and snap into place. Use one  
hand to hold the unit and use the other hand  
to clip the dirt container securely in place.  
Maintenance and care  
Cleaning the filter and screen  
1. Turn hand vacuum OFF.  
2. Unplug hand vacuum from electrical outlet.  
3. Disconnect dirt container and filter assembly  
4.  
from the unit.  
4. Remove filter by grasping tabs on both sides  
of filter frame and pulling away from the dirt  
container.  
5
w w w . b i s s e l l . c o m  
ug110-4076_87R4E_1008.indd  
5
12/10/08 3:31:19 PM  
 
Maintenance and care  
Cleaning the filter and screen continued  
5.  
6.  
5a.  
5. Separate filter assembly by grasping tabs on  
both sides of assembly and pull. For best results,  
periodically tap filter and screen against trash  
can to remove dirt that has collected.  
6. Reconnect filter and screen by aligning  
rectangular tab on filter with insert on screen.  
Press together to ensure assembly is secure.  
7. See page 5 to reattach dirt container.  
NOTE: The dirt container and screen may be  
rinsed with cold water. Ensure both are dry before  
reinserting. DO NOT RINSE PLEATED FILTER.  
Storage/Cord wrap system  
A wrap is attached to the cord for quick and  
easy storage.  
1. To store the unit, turn hand vacuum OFF.  
2. Unplug hand vacuum from electrical outlet.  
Insert  
Tab  
3. Bundle cord, using wrap that is located on  
cord, to store.  
Nozzle Maintenance  
Keep nozzles clean and free of debris.  
1. Wipe nozzles clean with damp cloth.  
Troubleshooting  
Hand vacuum won’t run  
Possible causes  
Remedies  
1. Power cord not plugged in  
1. Check electrical plug  
2. Thermal protector is activated  
2. Turn OFF and unplug the unit. Empty dirt  
container, clean filter and screen, and clear  
any clogs. Wait 30 minutes before turning  
the unit back on  
Hand Vacuum won’t pick up or low suction  
Possible causes  
Remedies  
1. Dirt container not installed properly  
1. Check assembly of dirt container making  
sure it is snapped in  
2. Dirt container is full  
2. Empty dirt container and reattach  
3. See instructions above. Replace filter if needed  
4. Wipe tools clean with damp cloth  
3. Filter or screen is dirty  
4. Nozzles are clogged with debris  
Other maintenance or service not included in the manual should be performed by an  
authorized service representative.  
Please do not return this product to the store.  
w w w . b i s s e l l . c o m  
6
ug110-4076_87R4E_1008.indd  
6
12/10/08 3:31:19 PM  
 
BISSELL Consumer Services  
If your BISSELL product should require service:  
In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give  
you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local  
in country distributor for questions, service, or repair.  
If you have questions about your warranty or need replacement parts please contact the numbers below.  
For UK inquiries:  
For Australian inquiries:  
Monday - Thursday 9 am — 5 pm  
Friday 9 am — 4 pm  
Monday - Friday 9 am — 5 pm  
BISSELL AUSTRALIA PTY LIMITED  
Unit 35  
BISSELL Homecare (Overseas) Inc.  
The Boat Yard  
15 Ricketts Road  
Mount Waverley, Victoria 3149  
Australia  
105 Straight Road  
Old Windsor  
Telephone: 1-800-811-183  
Berkshire, SL4 2SE  
United Kingdom  
Telephone: 0870-225-0109  
For all other inquiries:  
For New Zealand inquiries:  
Monday - Friday 9 am — 5 pm  
Monday - Friday 8 am — 4 pm  
Parex Industries Ltd.  
5 Tolich Place  
BISSELL Homecare, Inc.  
PO Box 1888  
Grand Rapids, MI 49501 USA  
Telephone: 01-616-453-4451  
Fax: 01-616-453-1383  
Henderson 0610  
Auckland  
New Zealand  
Telephone: 0800-247-735  
Or visit the BISSELL website - www.bissell.com  
When contacting BISSELL, have model number of unit available.  
Please record your Model Number: ___________________  
Please record your Purchase Date: ___________________  
Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a  
warranty claim. See Warranty on page 8 for details.  
Please do not return this product to the store.  
Replacement parts - BISSELL vacuum  
Item  
1
Part No.  
203-1432  
Part Name  
HEPA Media Filter Assembly  
2
3
1
203-1408  
203-1409  
2
Flexible Rubber Contour Nozzle  
Hard Nozzle  
3
7
w w w . b i s s e l l . c o m  
ug110-4076_87R4E_1008.indd  
7
12/10/08 3:31:19 PM  
 
Warranty - BISSELL Pet Hair EraserCorded Hand Vacuum  
This warranty gives you specific legal rights, and you may also have other rights which may vary from country  
to country. If you need additional instruction regarding this warranty or have questions regarding what it may  
cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or  
contact your local in country distributor.  
Limited One Year Warranty  
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with  
new or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the  
original purchaser, for one year any defective or malfunctioning part do to manufacturers defect.  
This warranty applies to product used for personal, and not commercial or rental service. This warranty does  
not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction  
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.  
For UK inquiries:  
For Australian inquiries:  
Monday - Thursday 9 am — 5 pm  
Friday 9 am — 4 pm  
Monday - Friday 9 am — 5 pm  
BISSELL AUSTRALIA PTY LIMITED  
Unit 35  
BISSELL Homecare (Overseas) Inc.  
The Boat Yard  
15 Ricketts Road  
Mount Waverley, Victoria 3149  
Australia  
105 Straight Road  
Old Windsor  
Telephone: 1-800-811-183  
Berkshire, SL4 2SE  
United Kingdom  
Telephone: 0870-225-0109  
For all other inquiries:  
For New Zealand inquiries:  
Monday - Friday 9 am — 5 pm  
Monday - Friday 8 am — 4 pm  
Parex Industries Ltd.  
5 Tolich Place  
BISSELL Homecare, Inc.  
PO Box 1888  
Grand Rapids, MI 49501 USA  
Telephone: 01-616-453-4451  
Fax: 01-616-453-1383  
Henderson 0610  
Auckland  
New Zealand  
Telephone: 0800-247-735  
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL  
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT.  
BISSELLS LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.  
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY  
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES  
EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE  
BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED ©2009 BISSELL Homecare, Inc  
Grand Rapids, Michigan  
TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS  
All rights reserved. Printed in Korea  
Part Number 110-4076  
Rev 10/08  
DESCRIBED ABOVE.  
Visit our website at:  
w w w . b i s s e l l . c o m  
8
ug110-4076_87R4E_1008.indd  
8
12/10/08 3:31:19 PM  
 

Black Box Switch AVSW HDMI8X8 X User Manual
Black Box Switch LB9017A R2 User Manual
Bosch Power Tools Power Hammer 11320VS User Manual
Braun Thermometer IRT4020 User Manual
Briggs Stratton Pressure Washer 20305 User Manual
Brinkmann Cell Phone 844 0350 0 User Manual
Brother Sewing Machine PC 2800 User Manual
Canon Printer MF9170 User Manual
Char Broil Charcoal Grill 4638247 User Manual
Christie Digital Systems Projector 38 VIV205 01 User Manual